View HCS11MS_508539.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

HCS11MS
November 1994
Radiation Hardened Triple 3-Input AND Gate
Pinouts
14 PIN CERAMIC DUAL-IN-LINE MIL-STD-1835 DESIGNATOR CDIP2-T14, LEAD FINISH C TOP VIEW
A1 1 B1 2 A2 3 B2 4 C2 5 Y2 6 GND 7 14 VCC 13 C1 12 Y1 11 C3 10 B3 9 A3 8 Y3
Features
* 3 Micron Radiation Hardened SOS CMOS * Total Dose 200K or 1 Mega-RAD(Si) * Dose Rate Upset >1010 RAD(Si)/s 20ns Pulse * Cosmic Ray Upset Immunity < 2 x 10-9 Errors/Gate Day (Typ) * Latch-Up Free Under Any Conditions * Military Temperature Range: -55oC to +125oC * Significant Power Reduction Compared to LSTTL ICs * DC Operating Voltage Range: 4.5V to 5.5V * Input Logic Levels - VIL = 30% of VCC Max - VIH = 70% of VCC Min * Input Current Levels Ii 5A at VOL, VOH
Description
The Intersil HCS11MS is a Radiation Hardened Triple 3Input AND Gate. A high on all inputs forces the output to a High state. The HCS11MS utilizes advanced CMOS/SOS technology to achieve high-speed operation. This device is a member of radiation hardened, high-speed, CMOS/SOS Logic Family. The HCS11MS is supplied in a 14 lead Weld Seal Ceramic flatpack (K suffix) or a Weld Seal Ceramic Dual-In-Line Package (D suffix).
14 PIN CERAMIC FLAT PACK MIL-STD-1835 DESIGNATOR CDFP3-F14, LEAD FINISH C TOP VIEW
A1 B1 A2 B2 C2 Y2 GND 1 2 3 4 5 6 7 14 13 12 11 10 9 8 VCC C1 Y1 C3 B3 A3 Y3
Truth Table
INPUTS An L L L L H H H H Bn L L H H L L H H Cn L H L H L H L H OUTPUTS Yn L L L L L L L H
Functional Diagram
(1, 3, 9) An
(2, 4, 10) Bn
(12, 6, 8) Yn
(13, 5, 11) Cn
NOTE: L = Logic Level Low, H = Logic level High
CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures. 1-888-INTERSIL or 321-724-7143 | Copyright (c) Intersil Corporation 1999
File Number
3048
7-135
Specifications HCS11MS
Absolute Maximum Ratings
Supply Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.5V to +7.0V Input Voltage Range, All Inputs . . . . . . . . . . . . .-0.5V to VCC +0.5V DC Input Current, Any One Input . . . . . . . . . . . . . . . . . . . . . . . .10mA DC Drain Current, Any One Output. . . . . . . . . . . . . . . . . . . . . . .25mA (All Voltage Reference to the VSS Terminal) Storage Temperature Range (TSTG) . . . . . . . . . . . -65oC to +150oC Lead Temperature (Soldering 10sec) . . . . . . . . . . . . . . . . . . +265oC Junction Temperature (TJ) . . . . . . . . . . . . . . . . . . . . . . . . . . +175oC ESD Classification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Class 1
Reliability Information
Thermal Impedance . . . . . . . . . . . . . . . . ja jc Weld Seal DIC . . . . . . . . . . . . . . . . . . . 75oC/W 16oC/W 12oC/W Weld Seal Flat Pack . . . . . . . . . . . . . . 64oC/W Power Dissipation per Package (PD) For TA = -55oC to +100oC . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1W For TA = +100oC to +125oC Derate Linearly at 13mW/oC
CAUTION: As with all semiconductors, stress listed under "Absolute Maximum Ratings" may be applied to devices (one at a time) without resulting in permanent damage. This is a stress rating only. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. The conditions listed under "Electrical Performance Characteristics" are the only conditions recommended for satisfactory device operation..
Operating Conditions
Supply Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . +4.5V to +5.5V Input Rise and Fall Times at 4.5V VCC (TR, TF) . . . . . 100ns/V Max Operating Temperature Range (TA) . . . . . . . . . . . . -55oC to +125oC Input Low Voltage (VIL). . . . . . . . . . . . . . . . . . . 0.0V to 30% of VCC Input High Voltage (VIH) . . . . . . . . . . . . . . . . . . 70% of VCC to VCC
TABLE 1. DC. ELECTRICAL PERFORMANCE CHARACTERISTICS GROUP A SUBGROUPS 1 2, 3 1 2, 3 1 2, 3 1, 2, 3 1, 2, 3 1, 2, 3 1, 2, 3 1 2, 3 7, 8A, 8B LIMITS TEMPERATURE +25oC +125oC, -55oC +25oC +125oC, -55oC +25oC +125oC, -55oC +25oC, +125oC, -55oC +25oC, +125oC, -55oC +25oC, +125oC, -55oC +25oC, +125oC, -55oC +25oC +125oC, -55oC +25oC, +125oC, -55oC MIN 4.8 4.0 -4.8 -4.0 VCC -0.1 VCC -0.1 MAX 10 200 0.1 0.1 0.5 5.0 UNITS A A mA mA mA mA V V V V A A -
PARAMETERS Quiescent Current
SYMBOL ICC
(NOTE 1) CONDITIONS VCC = 5.5V, VIN = VCC or GND VCC = 4.5V, VIH = 4.5V, VOUT = 0.4V, VIL = 0V VCC = 4.5V, VIH = 4.5V, VOUT = VCC -0.4V, VIL = 0V VCC = 4.5V, VIH = 3.15V, IOL = 50A, VIL = 1.35V VCC = 5.5V, VIH = 3.85V, IOL = 50A, VIL = 1.65V
Output Current (Sink) Output Current (Source) Output Voltage Low
IOL
IOH
VOL
Output Voltage High
VOH
VCC = 4.5V, VIH = 3.15V, IOH = -50A, VIL = 1.35V VCC = 5.5V, VIH = 3.85V, IOH = -50A, VIL = 1.65V
Input Leakage Current Noise Immunity Functional Test NOTE:
IIN
VCC = 5.5V, VIN = VCC or GND VCC = 4.5V, VIH = 0.70(VCC), VIL = 0.30(VCC) (Note 2)
FN
1. All voltages reference to device GND. 2. For functional tests VO 4.0V is recognized as a logic "1", and VO 0.5V is recognized as a logic "0".
All Intersil semiconductor products are manufactured, assembled and tested under ISO9000 quality systems certification.
Intersil products are sold by description only. Intersil Corporation reserves the right to make changes in circuit design and/or specifications at any time without notice. Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be accurate and reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries. For information regarding Intersil Corporation and its products, see web site http://www.intersil.com
7-136
Specifications HCS11MS
TABLE 2. AC ELECTRICAL PERFORMANCE CHARACTERISTICS GROUP A SUBGROUPS 9 10, 11 Input to Yn TPLH VCC = 4.5V 9 10, 11 NOTES: 1. All voltages referenced to device GND. 2. AC measurements assume RL = 500, CL = 50pF, Input TR = TF = 3ns, VIL = GND, VIH = VCC. LIMITS TEMPERATURE +25oC +125oC, -55oC +25oC +125oC, -55oC MIN 2 2 2 2 MAX 18 20 20 22 UNITS ns ns ns ns
PARAMETER Input to Yn
SYMBOL TPHL
(NOTES 1, 2) CONDITIONS VCC = 4.5V
TABLE 3. ELECTRICAL PERFORMANCE CHARACTERISTICS LIMITS PARAMETER Capacitance Power Dissipation Input Capacitance SYMBOL CPD CONDITIONS VCC = 5.0V, f = 1MHz NOTES 1 1 CIN VCC = Open, f = 1MHz 1 1 Output Transition Time NOTE: 1. The parameters listed in Table 3 are controlled via design or process parameters. Min and Max Limits are guaranteed but not directly tested. These parameters are characterized upon initial design release and upon design changes which affect these characteristics. TTHL TTLH VCC = 4.5V 1 1 TEMPERATURE +25oC +125oC +25oC +125oC +25oC +125oC MIN MAX UNITS pF pF pF pF ns ns
Typical 20 Typical 30 10 10 15 22
TABLE 4. DC POST RADIATION ELECTRICAL PERFORMANCE CHARACTERISTICS (NOTES 1, 2) CONDITIONS VCC = 5.5V, VIN = VCC or GND VCC = 4.5V, VIN = VCC or GND, VOUT = 0.4V VCC = 4.5V, VIN = VCC or GND, VOUT = VCC -0.4V VCC = 4.5V and 5.5V, VIH = 0.70(VCC), VIL = 0.30(VCC) at 200K RAD, VIL = 0.12(VCC) at 1M RAD, IOL = 50A VCC = 4.5V and 5.5V, VIH = 0.70(VCC), VIL = 0.30(VCC) at 200K RAD, VIL = 0.12(VCC) at 1M RAD, IOH = -50A VCC = 5.5V, VIN = VCC or GND VCC = 4.5V, VIH = 0.70(VCC), VIL = 0.30(VCC) at 200K RAD, VIL = 0.12(VCC) at 1M RAD (Note 3) TEMPERATURE +25oC +25oC +25oC +25oC 200K RAD LIMITS MIN 4.0 -4.0 MAX 0.2 0.1 1M RAD LIMITS MIN 4.0 -4.0 MAX 1.0 0.1 UNITS mA mA mA V
PARAMETERS Quiescent Current Output Current (Sink) Output Current (Source) Output Voltage Low
SYMBOL ICC IOL IOH VOL
Output Voltage High
VOH
+25oC
VCC -0.1
-
VCC -0.1
-
V
Input Leakage Current Noise Immunity Functional Test
IIN FN
+25oC +25oC
-
5 -
-
5 -
A -
7-137
Specifications HCS11MS
TABLE 4. DC POST RADIATION ELECTRICAL PERFORMANCE CHARACTERISTICS (Continued) (NOTES 1, 2) CONDITIONS VCC = 4.5V VCC = 4.5V TEMPERATURE +25oC +25oC 200K RAD LIMITS MIN 2 2 MAX 20 22 1M RAD LIMITS MIN 2 2 MAX 25 28 UNITS ns ns
PARAMETERS Data to Output
SYMBOL TPHL TPLH
NOTES: 1. All voltages referenced to device GND. 2. AC measurements assume RL = 500, CL = 50pF, Input TR = TF = 3ns, VIL = GND, VIH = VCC. 3. For functional tests VO 4.0V is recognized as a logic "1", and VO 0.5V is recognized as a logic "0".
TABLE 5. BURN-IN AND OPERATING LIFE TEST, DELTA PARAMETERS (+25oC) GROUP B SUBGROUP 5 5
PARAMETER ICC IOL/IOH
DELTA LIMIT 3A -15% of 0 Hour
TABLE 6. APPLICABLE SUBGROUPS CONFORMANCE GROUPS Initial Test (Preburn-In) Interim Test I (Postburn-In) Interim Test II (Postburn-In) PDA Interim Test III (Postburn-In) PDA Final Test Group A (Note 1) Group B Subgroup B-5 Subgroup B-6 Group D NOTE: 1. Alternate group A inspection in accordance with method 5005 of MIL-STD-883 may be exercised. METHOD 100%/5004 100%/5004 100%/5004 100%/5004 100%/5004 100%/5004 100%/5004 Sample/5005 Sample/5005 Sample/5005 Sample/5005 GROUP A SUBGROUPS 1, 7, 9 1, 7, 9 1, 7, 9 1, 7, 9, Deltas 1, 7, 9 1, 7, 9, Deltas 2, 3, 8A, 8B, 10, 11 1, 2, 3, 7, 8A, 8B, 9, 10, 11 1, 2, 3, 7, 8A, 8B, 9, 10, 11, Deltas 1, 7, 9 1, 2, 3, 7, 8A, 8B, 9, 10, 11 Subgroups 1, 2, 3, 9, 10, 11 ICC, IOL/H READ AND RECORD ICC, IOL/H ICC, IOL/H ICC, IOL/H
TABLE 7. TOTAL DOSE IRRADIATION CONFORMANCE GROUPS Group E Subgroup 2 NOTE: 1. Except FN test which will be performed 100% Go/No-Go. TEST METHOD 5005 PRE RAD 1, 7, 9 POST RAD Table 4 READ AND RECORD PRE RAD 1, 9 POST RAD Table 4 (Note 1)
TABLE 8. STATIC AND DYNAMIC BURN-IN TEST CONNECTIONS OSCILLATOR OPEN GROUND 1/2 VCC = 3V 0.5V VCC = 6V 0.5V 50kHz 25kHz
STATIC BURN-IN I TEST CONDITIONS (Note 1)
7-138
Specifications HCS11MS
TABLE 8. STATIC AND DYNAMIC BURN-IN TEST CONNECTIONS OSCILLATOR OPEN 6, 8, 12 GROUND 1, 2, 3, 4, 5, 7, 9, 10, 11, 13 1/2 VCC = 3V 0.5V VCC = 6V 0.5V 14 50kHz 25kHz -
STATIC BURN-IN II TEST CONNECTIONS (Note 1) 6, 8, 12 7 1, 2, 3, 4, 5, 9, 10, 11, 13, 14 -
DYNAMIC BURN-IN I TEST CONNECTIONS (Note 2) NOTES: 1. Each pin except VCC and GND will have a resistor of 10K 5% for static burn-in. 2. Each pin except VCC and GND will have a resistor of 680K 5% for dynamic burn-in. 7 6, 8, 12 14 1, 2, 3, 4, 5, 9, 10, 11, 13 -
TABLE 9. IRRADIATION TEST CONNECTIONS OPEN 6, 8, 12 GROUND 7 VCC = 5V 0.5V 1, 2, 3, 4, 5, 9, 10, 11, 13, 14
AC Timing Diagrams
VIH VS VIL TPLH TPHL VOH INPUT
AC Load Circuit
DUT TEST POINT CL RL
CL = 50pF VS VOL TTLH 80% VOL 20% 80% 20% TTHL OUTPUT RL = 500
VOH
OUTPUT
AC VOLTAGE LEVELS PARAMETER VCC VIH VS VIL GND HCS 4.50 4.50 2.25 0 0 UNITS V V V V V
7-139
HCS11MS Die Characteristics
DIE DIMENSIONS: 87 x 88 mils 2.20 x 2.24mm METALLIZATION: Type: AlSi Metal Thickness: 11kA 1kA GLASSIVATION: Type: SiO2 Thickness: 13kA 2.6kA DIE ATTACH: Material: Silver Epoxy WORST CASE CURRENT DENSITY: <2.0 x 105A/cm2 BOND PAD SIZE: 100m x 100m 4 x 4 mils
Metallization Mask Layout
HCS11MS
A1 (1) VCC (14) C1 (13)
B1 (2)
(12) Y1
(11) C3 A2 (3)
B2 (4)
(10) B3
C2 (5)
(9) A3
(6) Y2
(7) GND
(8) Y3
7-140

▲Up To Search▲

Price & Availability of HCS11MS

	To Download HCS11MS Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .